Home > Portable Table Saw Reviews, Portable Table Saws, Table Saw Buying Guide > If You’d Like To Buy A Table Saw, Understand You Have To Know All Your Wood working

If You’d Like To Buy A Table Saw, Understand You Have To Know All Your Wood working

Listed below are popular table saw and woodworking terms, key phrases and definitions.

To be able to install, appreciate functions, modify or conduct any table saw, you should know more about these woodworking terms.

Anti-Kickback Pawls — A device that, when effectively set up and serviced, is designed to stop the workpiece from being forced back toward the front of the saw during the ripping operation.

Arbor — The shaft that hooks up the saw blade, located on the drive mechanism.

Bevel Cut — A cutting operation made with the blade with any angle apart from 90 degrees to the table surface.

Blade Guard Assembly — Metal or maybe plastic safety application that is attached on the saw blade. Itperforms by stopping the owner from touching the blade.

Compound Cut — This is done when a cross cut is made making use of each a bevel angle as well as a miter.

Cross Cut — A cutting or shaping process made across the grain or the width of the material.

Cutterhead — This is a revolving cutterhead that has flexible knives or even blades. The blades or knives eliminate material from the workpiece.

Dado Blade — An individual blade or collection of blades used to cut rabbets as well as grooves.

Dado Cut — Cutting procedure which utilizes a dado blade to cut a flat based groove to the workpiece.

Featherboard — Protective device utilized to retain the workpiece against the rip fence and also against the table surface.

FPM or SPM — It means the motion of the blade in feet per minute or strokes per minute.

Freehand — Conducting a cut without the workpiece remaining directed by a miter gauge, fence or any other device.

Heel — The placement of the blade towards the fence.

Kerf — The gap or ensuing cut in the material during a cutting procedure.

Kickback — An incident where the material is forced back towards the owner with a high rate.

Miter Cut — Performing a cut in the workpiece at any perspective towards the blade besides 90°.

Non-Through Cut — A cut in which the blade does not cut through the entire thickness of the material.

Parallel — Having the same distance apart at each point alongside two presented planes or lines.

Perpendicular — Intersecting planes or lines creating right-angles. For example, the blade is perpendicular to the table surface.

Pilot Hole (drill presses) — A small hole drilled in a workpiece that serves as a lead for drilling big holes perfectly.

Push Stick — A piece of safety tool being utilized in driving the workpiece during a cutting process. Utilized normally when rip cutting lean materials. This aid keeps the hands of the operator away from the blade.

Rabbet — Cutting procedure that creates an L-shaped channel across the side of the material.

Resaw — A cutting process to minimize the size of a material to make thinner parts.

Resin — A solidified sticky, sap-based element.

Revolutions Per Minute (RPM) — The number of rotations completed by a spinning object in one minute.

Rip Cut — Cutting operation in which the rip fence is utilized to cut through the entire workpiece.

Riving Knife/Spreader/Splitter — A metal plate which preserves the kerf opening within the wood on a cutting operation and is situated behind the blade.

Saw Blade Path — The area above, below, at the rear of, or in front of the blade. The area which will be cut or has been already cut by the blade.

Set — The outward bend (or set) range of the tip of the saw on the face of the table.

Snipe (planers) — When the workpiece is not accordingly supported, it generates a depression at either end of a work piece by cutter blades.

Straightedge — An instrument employed to check the flatness, parallelism, or regularity of a surface(s).

Thin Kerf Blade — The kerf or thickness of a blade slimmer compared to a normal blade.

Through Cut — A cut where the blade cuts completely over the thickness of the material.

Throw-Back — If the workpiece is dropped to the blade or set accidentally in contact with the blade, the throwing back of a material is made.

Worktable — It is the surface where the material lies during a cutting, drilling, planing, or sanding process.

Click the following link for information, buyer reviews, comments and feedback if you are looking to buy a table saw.

Advertisements
  1. No comments yet.
  1. No trackbacks yet.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

%d bloggers like this: